By product form

Thermocouple Stranded Wire

Stranded thermocouple wire is the multi-strand twisted form of the same five standard alloy pairs, built as 7, 19 or 37 strand constructions from φ0.1 mm to φ5.0 mm. Each product page below carries the full specification table, alloy designation, EMF tolerance and the certification scope you get with the batch.

Available types, Stranded Wire

Specifying a stranded wire conductor

Choose stranded wire whenever the conductor moves. Vibration, flexing and repeated thermal cycling work-harden a solid conductor until it fractures at the junction or along the run, a 7, 19 or 37 strand construction distributes that strain across the individual strands instead. It is the correct form for moving parts, vibrating equipment, tight routing radii and any installation where the wire is handled or repositioned during maintenance.

  1. Confirm the alloy pair and the temperature range for your process, the five standard types covered here are K, N, J, T and E.
  2. Pick the strand configuration (7, 19 or 37) and the finished conductor diameter from φ0.1 mm to φ5.0 mm.
  3. Set the temper and finish, annealed tempers are usual where the multi-strand conductor has to flex in service.

Stranded wire supply details

Construction
7 / 19 / 37 strand construction
Diameter range
φ0.1 mm, φ5.0 mm, starts at φ0.1 mm because strand lay sets a practical floor on the finished conductor diameter, below that the individual strands are too fine to twist reliably.
Surface finish
Bright / Oxidized / Electro-polished
Condition
Hard (cold-drawn) / Soft (annealed) / Bright finished
Packaging
DIN 125 / 160 / 250 / 355 spool / Coil / Custom reel

Stranded wire or bare wire?

Bare and stranded wire are made from the same five alloy pairs to the same IEC 60584-1 Class 1 and ASTM E230 tolerances. The difference is the conductor construction, and that is what decides which form suits an installation.

AspectStranded WireBare Wire
Conductor construction7 / 19 / 37 twisted strandsSolid single strand
Diameter rangeφ0.1 mm, φ5.0 mmφ0.025 mm, φ5.0 mm
Best suited toMoving, flexing or vibrating conductorsFixed sensing points and ultra-fine gauge junctions

Every conductor ships with a mill test certificate, EMF calibration certificate and furnace batch traceability. Tell us the alloy, diameter, finish, temper and coil weight and we return a priced offer.

Request a quote

What is stranded thermocouple wire?

Stranded thermocouple wire is multiple thin alloy strands twisted into a flexible conductor, made for installations where the wire moves. RAS Thermal supplies it in Type K, N, J, T and E in 7, 19 or 37 strand constructions, from φ0.1 mm to φ5.0 mm, to IEC 60584-1 Class 1 and/or ASTM E230.

Strand count and when to choose stranded wire

Vibration, flexing and thermal cycling work-harden a solid conductor until it fractures, a stranded construction lasts several times longer in those conditions. Higher strand counts, 19 and 37 · give progressively greater flexibility and flex-cycle life for the same cross-section, while 7-strand is the economical entry point for mild flexing.

Stranded thermocouple wire types

Stranded wire FAQs

When should stranded wire be chosen over bare?

Whenever the wire moves. Vibration, flexing and thermal cycling work-harden a solid conductor until it fractures, stranded construction lasts several times longer in those conditions.

What strand constructions and diameters are available?

7, 19 or 37 strands, in diameters from φ0.1 mm to φ5.0 mm.

Does stranding change the EMF tolerance?

No, stranded and bare conductors are the same alloys made to the same standard, the EMF tolerance is set by the standard, not the construction.

Add RAS Thermal as a preferred source on Google