By product form

Thermocouple Bare Wire

Bare thermocouple wire is the solid, single-strand form of the five standard alloy pairs, supplied from φ0.025 mm up to φ5.0 mm. Each product page below carries the full specification table, alloy designation, EMF tolerance and the certification scope you get with the batch.

Available types, Bare Wire

Specifying a bare wire conductor

Choose bare wire when the conductor is fixed in service. A solid single strand gives a stable, repeatable EMF at the junction, holds its calibrated tolerance along a straight run, and is the simplest thing to weld, braze or twist into a measuring point. Because there is no strand lay and no insulation to strip, it is also the form to specify when the junction itself has to be formed on site.

  1. Confirm the alloy pair and the temperature range for your process, the five standard types covered here are K, N, J, T and E.
  2. Pick the conductor diameter from φ0.025 mm to φ5.0 mm, ultra-fine gauges are made as solid single strand.
  3. Set the surface finish and temper, bright, oxidized or electro-polished, in hard-drawn or annealed condition.

Bare wire supply details

Construction
Solid single strand
Diameter range
φ0.025 mm, φ5.0 mm, runs down to φ0.025 mm at the ultra-fine end, which is where bare wire is normally specified, fine-gauge junctions and fast-response sensing points.
Surface finish
Bright / Oxidized / Electro-polished
Condition
Hard (cold-drawn) / Soft (annealed) / Bright finished
Packaging
DIN 125 / 160 / 250 / 355 spool / Coil / Custom reel

Bare wire or stranded wire?

Bare and stranded wire are made from the same five alloy pairs to the same IEC 60584-1 Class 1 and ASTM E230 tolerances. The difference is the conductor construction, and that is what decides which form suits an installation.

AspectBare WireStranded Wire
Conductor constructionSolid single strand7 / 19 / 37 twisted strands
Diameter rangeφ0.025 mm, φ5.0 mmφ0.1 mm, φ5.0 mm
Best suited toFixed sensing points and ultra-fine gauge junctionsMoving, flexing or vibrating conductors

Every conductor ships with a mill test certificate, EMF calibration certificate and furnace batch traceability. Tell us the alloy, diameter, finish, temper and coil weight and we return a priced offer.

Request a quote

What is bare thermocouple wire?

Bare thermocouple wire is solid single-strand alloy conductor with no insulation or sheath, the raw sensing element used to build thermocouples, extension junctions and calibration assemblies. RAS Thermal supplies it in Type K, N, J, T and E, from φ0.025 mm ultra-fine to φ5.0 mm standard, in bright or oxidised finish, to IEC 60584-1 Class 1 and/or ASTM E230.

When to choose bare wire over stranded

Choose bare wire for static installations, furnace sensing elements, panel wiring and calibration standards, where the conductor stays fixed. A solid conductor work-hardens under vibration, flexing or thermal cycling and eventually fractures. If the wire moves, specify stranded construction instead.

Bare thermocouple wire types

Bare wire FAQs

What diameters does bare wire come in?

From φ0.025 mm ultra-fine to φ5.0 mm standard, with ±0.005 mm tolerance on fine sizes and ±0.02 mm on standard sizes.

Can bare wire be used where it will vibrate?

Not for sustained service. Vibration and flexing work-harden a solid conductor until it fractures, specify stranded wire for moving installations.

What finishes and packaging are available?

Bright, oxidised or electro-polished finish, in hard (cold-drawn), soft (annealed) or bright-finished condition, on DIN 125 / 160 / 250 / 355 spool, coil or custom reel.

Add RAS Thermal as a preferred source on Google